Replacing the Water Filter

Replacing the Water Filter – A Step-by-Step Guide

If you have a refrigerator with a water dispenser or an ice maker, you probably have a water filter that needs to be replaced periodically. The water filter helps to remove contaminants and impurities from the water supply, ensuring that you have clean and fresh water and ice. However, over time, the filter can get clogged or lose its effectiveness, which can affect the taste, odor, and quality of your water and ice. That’s why it’s important to replace your water filter regularly, usually every 6 months or as recommended by the manufacturer. Need your Kitchen Aid Refrigerator Repair in Santa Barbara? Our trusted partner is ready to help. Seek their expertise for dependable repair services. We’re here to support your needs

Replacing the water filter is not a difficult task, but it may vary depending on the type and model of your refrigerator. In this article, we will show you how to replace the water filter in some of the most common types of refrigerators, such as:

• Refrigerators with a filter in the base grille
• Refrigerators with a filter in the upper right-hand corner inside
• Refrigerators with a filter in the back, upper-right corner inside
• Refrigerators with an inline filter behind the unit

Before you start, make sure you have the correct replacement filter for your refrigerator model. You can find the filter number printed on the old filter or in the owner’s manual. You can also search online by entering your refrigerator model number and the word “filter”. You can buy the replacement filter from the manufacturer’s website or from other online retailers.

Refrigerators with a Filter in the Base Grille

Some refrigerators have a water filter located in the base grille at the bottom of the unit. To replace this type of filter, follow these steps:

1. Locate the filter cap below the fridge’s lowest door. Place a towel or cloth on the floor below the filter to catch drips.
2. Twist the filter cap or knob counterclockwise until you can feel that it’s free of its mount.
3. Remove the filter by pulling it straight out towards you.
4. Open your new filter and remove the protective coverings from the O-rings. Make sure the O-rings are still in place after the cover has been removed.
5. When inserting the new filter into the slot, make sure the arrow is pointing upward. Do not force the water filter. If it does not slide in easily, rotate it until the notches are properly aligned with the grooves.
6. Push the filter all the way in until it stops.
7. Turn the filter cap or knob clockwise until it locks into place.
8. Once your filter is replaced, run about 2 gallons of water through the dispenser to flush out any air and debris from the system.
9. Reset the filter status light or indicator according to your refrigerator model.

Refrigerators with a Filter in the Upper Right-Hand Corner Inside

Some refrigerators have a water filter located in the upper right-hand corner inside the refrigerator compartment. To replace this type of filter, follow these steps:

1. Locate your water filter cover in the upper right-hand corner inside your refrigerator or in the base grille.
2. Lift or pull open the filter door.
3. Pull or twist off (depending on model)the old filter and discard it.
4. Open your new filter and remove any protective coverings from it.
5. When inserting your new filter into its slot, make sure that it is oriented correctly according to your model (some filters have arrows or labels that indicate which way they should go).
6. Push or twist on (depending on model)the new filter until it snaps into place.
7. Close or snap shut (depending on model)the filter door.
8. Once your filter is replaced, run about 2 gallons of water through your dispenser to flush out any air and debris from your system.
9. Reset your change-filter light according to your refrigerator model.

Refrigerators with a Filter in the Back, Upper-Right Corner Inside

Some refrigerators have a water filter located in the back, upper-right corner inside
the refrigerator compartment. To replace this type of filter, follow these steps:

1. Locate your water filter cover in
   the back, upper-right corner inside
   your refrigerator.
2. Pull open
   the cover by squeezing both tabs
   and pulling outward.
3. Turn
   the old
   filter counterclockwise until it releases from
   the housing.
4. Pull out
   the old
   filter and discard it.
5. Open your new
   filter and remove any protective coverings from it.
6. When inserting
   your new
   filter into its slot,
   make sure that it is oriented correctly according to your model (some filters have arrows or labels that indicate which way they should go).
7. Push
   the new
   filter into
   the housing until it stops.
8. Turn
   the new
   filter clockwise until it locks into place.
9. Close
   the cover by pushing it inward until it snaps shut.
10. Once your filter is replaced,
    run about 2 gallons of water through your dispenser to flush out any air and debris from your system.
11. Reset your change-filter light according to your refrigerator model.

Refrigerators with an Inline Filter Behind the Unit

Some refrigerators have an inline water filter installed directly in the refrigerator’s water line, accessed from the back of the fridge. Replacing these sorts of filters is a little more involved, but still doable! You may need a pair of pliers and possibly a screwdriver to replace this type of filter. Follow these steps:

1. Pull the refrigerator out and away from the wall.
2. Unplug the refrigerator or turn off the breaker for the unit.
3. Turn off the water supply valve that runs to the refrigerator.
4. Place a bucket or towel under the inline water filter.
5. Take the filter housing from its case.
6. Disconnect the filter from the water line by loosening the nuts or clamps on both ends of the filter.
7. Pull the supply lines from the filter and remove any fittings.
8. Screw or connect the new filter into the fittings.
9. Reconnect the water supply lines to the supply valve and to the filter.
10. Turn on the water and check for any leaks. Tighten the nuts or clamps if needed.
11. Plug in the refrigerator or turn on the breaker for the unit.
12. Push the refrigerator back to its original position.
13. Once your filter is replaced, run about 2 gallons of water through your dispenser to flush out any air and debris from your system.

Conclusion

Replacing your refrigerator water filter is an easy and important task that can improve
the quality and taste of your water and ice. By following these simple steps, you can
replace your water filter in no time and enjoy fresh and clean water and ice for months
to come.

If you need any help with replacing your water filter or any other appliance repair
services, you can always contact us at Boston Appliance Repair Pros. We are a team of
professional and experienced technicians who can handle any appliance issue you may
have. We offer fast, reliable, and affordable service for all your appliance needs.

To schedule an appointment with us, you can call us or visit our website. We look forward to hearing from you and serving you with excellence!